FREE Shipping on orders over $150 (Weight Restrictions Apply)
11.4 L/min flow. 1,000 psi working pressure. Low-speed induction motor. Patented 5-piston serviceable pump. The ACTIVE 3.0 is the flagship of the Active range, built on the idea that flow matters more than pressure. More water moving over the panel rinses faster, carries foam better and lifts dirt with less force, which is what you want on paintwork.
Best ACTIVE for detailers who want maximum flow and a pump they can service, in a machine quiet enough to run in a residential driveway.
| Task | Suitability |
|---|---|
| Pre-wash and rinsing | ExcellentThis is what the flow rate buys you. Rinsing is noticeably faster than a lower-flow machine. |
| Snow foam through a cannon | ExcellentFoam cannons need flow to produce thick, clinging foam. A 1.65 mm foam cannon orifice is supplied. |
| Wheels and arches | Excellent |
| Driveways, patios and hard surfaces | Excellent |
| Daily commercial detailing use | ExcellentInduction motor and serviceable pump are what make sustained daily use realistic. |
| Engine bays | SuitableUse a wide fan nozzle and keep your distance from electrical connections. |
| Heavily caked machinery or concrete | Check requirementsThis is a flow machine tuned for vehicles. Heavy industrial cleaning wants more pressure. |
| Hot water cleaning | Not suitableCold water only, maximum inlet temperature 40 degrees. |
Suitability above is general guidance based on the machine's published flow and pressure against typical detailing tasks, not a performance guarantee. Results depend on your water supply, nozzle selection, chemical and technique.
Pressure washers are usually sold on pressure, because it is the bigger and more impressive number. For detailing it is the wrong number to lead with.
Pressure is force. It is what strips paint from a fence, and it is also what damages trim, lifts badges and forces water past seals if you get too close to a car.
Flow is volume. It is what carries dirt off the panel and away, what makes foam thick enough to cling and dwell, and what lets you rinse a whole car quickly.
At 11.4 litres a minute the ACTIVE 3.0 sits well above most domestic electric machines, which typically manage 6 to 8. Working pressure is a deliberate 1,000 psi, which is plenty for a car and gentle enough not to risk the finish. That combination is the whole design philosophy.
The highest flow in the ACTIVE range, and high for any electric machine. Faster rinsing, better foam, less time per car.
Quieter at around 75 dB, cooler running and longer lasting than the universal motors used in cheaper machines. It is the single biggest difference between a machine that lasts and one that does not.
Five pistons deliver smoother, more consistent flow than a three-piston pump. Oil-filled with dedicated fill and drain ports, so you service it rather than replace the machine.
Seals, valves and pistons use better materials and treatments than the 2.0 and 2.3, specifically for longer running life.
Ships with a 1.65 mm foam cannon orifice, so aftermarket cannons work properly straight away rather than starving for flow.
Standard M22 connection, so hoses, guns, lances and cannons from the wider detailing market fit without adaptors.
| Specification | Detail |
|---|---|
| Maximum flow rate | 11.4 L/min (3.0 GPM)The figure to compare against other machines for detailing work. |
| Working pressure | 1,000 psi (69 bar)Tuned for vehicles. High enough to clean, low enough to be safe on paint, trim and seals. |
| Peak pressure | 1,500 psi (103 bar) |
| Motor | Low-speed induction |
| Pump | Patented 5-piston, serviceable, oil-filled with fill and drain ports |
| Voltage | 220 to 240V, 50 Hz |
| Plug | AU/NZ 15 AmpNot a standard 10 amp point. Confirm your outlet before ordering. |
| Noise level | Approximately 75 dB |
| Maximum inlet water temperature | 40 degrees Celsius |
| Outlet connection | M22 |
| Inlet connection | 3/4 inch, 11.5 TPINorth American garden hose thread. An adaptor may be needed for an Australian tap fitting. |
| Nozzle orifice | 6.3Four nozzles supplied. If changing them, ACTIVE recommend staying between 6.3 and 7.0 to keep the balance of pressure and flow. |
| Foam cannon orifice supplied | 1.65 mmSized to balance foam performance against electrical load. |
| Service interval | First 25 hours, then every 100 hours |
The serviceable pump is one of the main reasons to buy this machine over a sealed-unit alternative, but it only helps if you use it.
| Interval | Task |
|---|---|
| First 25 hours | Change the pump oil. This first change clears any particles from bedding in. |
| Every 100 hours after that | Change the pump oil. |
| Before each use | Check the inlet filter is clean. Grit reaching the pump is what kills valves and seals. |
| After each use | Release trigger pressure and disconnect. If storing somewhere cold, drain the pump. |
ACTIVE publish generator requirements for their pressure washers: 1,800 watts running and 3,000 watts surge. Every Westinghouse generator we stock clears that comfortably, including the smallest.
They also specify the water supply: at least 40 psi inlet pressure and more than 3 GPM flow. That matters more than most people expect, since a restricted tap will starve the pump regardless of what the machine is rated for.
No. The Australian and New Zealand version uses a 15 amp plug, which is physically larger than a standard 10 amp point and will not fit one. Do not use a 10 amp adaptor or extension lead to get around it. If you do not have a 15 amp outlet, an electrician will need to install one, or look at the ACTIVE 2.0 which runs on a standard point.
Pressure is force and flow is volume. Force is what damages trim and forces water past seals. Volume is what carries dirt off the panel and away. For paintwork you want plenty of water moving at moderate pressure, which is exactly how ACTIVE tune their machines. It is also why a high-flow machine makes noticeably better foam.
Universal motors are small, light, cheap and spin very fast, which makes them loud and hot. They are what most domestic pressure washers use. Induction motors run slower and cooler, are quieter, and last considerably longer under sustained use. They also cost more and weigh more, which is why you find them on professional machines.
Yes, and it will work better than on a lower-flow machine, because foam cannons need volume to produce thick clinging foam. A 1.65 mm foam cannon orifice is supplied for use with aftermarket cannons. The outlet is standard M22 so most guns, lances and cannons fit directly.
Change the pump oil after the first 25 hours, then every 100 hours. The pump has dedicated fill and drain ports so it is a straightforward job. Also keep the inlet filter clean, since grit reaching the pump is what destroys valves and seals, and never run the pump dry.
Yes, and this catches people out. A pump can only move the water that reaches it. If your tap or hose cannot sustain 11.4 L/min the machine will cavitate and underperform, which people often mistake for a faulty unit. Use a good quality hose with at least 5/16 inch internal diameter, and check your tap flow before blaming the machine.
Not beyond 40 degrees at the inlet. This is a cold water machine. Feeding it hot water will damage the pump seals.
Freight: this machine is overweight for Express Post or Parcel Post and must go by courier. Email us with your postcode for a delivery quote before ordering.
Please allow extra time for delivery to regional and remote areas.
Free Shipping on orders over $150 excluding remote areas and certain weight restrictions apply for free shipping in each state. Trade accounts $250 minimum for free shipping.
The following qualifies for free shipping:
For orders with free shipping, we determine whether to use a courier service or Australia Post based on the address. If you prefer your order to be shipped via Australia Post, please select the "Parcel Post" option at checkout.
Note: We do not ship to PO Boxes or Parcel Lockers with free shipping.
If your parcel is returned to us, the following conditions outline when additional shipping costs may apply:
*We will not be held responsible for delays or late delivery of Australia Post or courier services.
*If a parcel does not arrive as anticipated, please allow 5-7 working days for Australia Post or couriers to complete process of tracking and locating as in most cases it turns up after 3-7 days of expected delivery. We cannot refund or send another item until this process is completed.
*We don't take responsibility for orders that are lost or stolen once the parcel has been delivered to the correct delivery address.
*Items that are over 21kg may require to pay extra freight costs if in regional or remote areas - we will contact you if this is the case.
All of our prices are in Australian dollars (AUD) and include GST (Goods and services tax)
At Detailing Shed, we're a family-owned business that genuinely wants you to be happy with your purchase.
If something isn't right, please contact us before returning anything. In many cases, we can help resolve the issue with product advice, troubleshooting, or support from our team.
This policy explains how returns, refunds and warranty-related claims are handled while respecting your rights under Australian Consumer Law.
Nothing in this policy limits or replaces your rights under Australian Consumer Law.
If a product has a major or minor failure, you may be entitled to a remedy under Australian Consumer Law. The terms below primarily apply to change-of-mind purchases and circumstances not covered by consumer guarantees.
We may accept approved change-of-mind returns subject to the following conditions:
To request a return, email info@detailingshed.com.au with:
Due to safety, hygiene, freight and manufacturer restrictions, the following products are not eligible for change-of-mind returns:
These products cannot be returned for change of mind unless required under Australian Consumer Law.
With prior approval, we may accept returns on unused and unopened items such as:
Please contact us before sending anything back.
If you believe a product isn't performing correctly, please contact us before returning it.
To help us assess the issue, please provide:
In some cases, we may ask you to return the product for inspection.
If testing shows the product is operating as intended, the matter may be treated as a change-of-mind return and the standard conditions above may apply.
Products excluded from change-of-mind returns remain ineligible for return where no fault is found.
For orders shipped to New Zealand, customers are responsible for return shipping costs when sending back:
This applies to inspections, repairs and warranty-related claims.
Due to the high cost of international freight, we are unable to cover these return shipping costs.
If you've ordered the wrong item, you're welcome to return eligible products under this policy and place a new order for the correct item.
If you're unsure which product is right for you, our team is happy to help.
Orders can be cancelled before they have been processed or dispatched.
Approved cancellations will be refunded to the original payment method less a 3% payment processing fee.
Once an order has been processed or shipped, it can no longer be cancelled. However, eligible items may still be returned under our Change of Mind Returns policy.
If your order arrives damaged, incorrect or faulty, please contact us within 10 days of delivery.
Email info@detailingshed.com.au and include:
We'll work with you to assess the issue and determine an appropriate resolution.
If your parcel appears to be missing, we'll work with the carrier to investigate.
Please allow 7-15 business days for the investigation to be completed before a resolution can be finalised.
Manufacturers occasionally update packaging, labels and colours without notice.
As a result, the product you receive may vary slightly from the images shown on our website. This alone does not constitute a fault provided the correct product has been supplied.
Discount codes must be applied during checkout.
Unfortunately, discounts cannot be applied retrospectively and we cannot refund the difference after an order has been placed.
If you're experiencing issues with a discount code, please contact us before completing your purchase.
We're always happy to help.
Email: info@detailingshed.com.auinfo@detailingshed.com.au
When contacting us, please include:
Our team will do their best to resolve your enquiry quickly and fairly.
We're here to help
If you need to contact us for advice on any of the products, please email us at info@detailingshed.com.au
Please include description of the product you are interested. Some info of you car, and also what you are trying to achieve.
We may also review our blogs for product recommendations.
