FREE Shipping on orders over $150 (Weight Restrictions Apply)
WP iGen10000PRO
The Westinghouse iGen10000PRO is the only model in the range we rate for two machines. 8,200 running watts and 34.2 amps continuous is enough spare capacity to absorb a compressor cutting in while a pressure washer is already running, which is the moment that trips a smaller generator. You get two standard 15 amp outlets using the adaptor supplied in the box, the same RCD safety switch as the rest of the PRO range, and a 30 litre tank that runs up to 19.8 hours at quarter load.
In Australia a machine is either a 10 amp or a 15 amp machine. A 15 amp Kranzle plus a 10 amp compressor needs 25 amps of supply. That is the iGen7500PRO's entire rating, and only three quarters of this one.
Induction motors draw a large surge for the moment they start. The accepted sizing rule is two and a half times the motor's rating, or three times for a compressor that starts against tank pressure. A total stop pressure washer restarts every single time you pull the trigger, and a compressor cuts in on its own pressure switch whenever tank pressure drops. So the surge is not a one off at the start of the day, it is happening constantly, and it lands on a generator that is already carrying the other machine.
That is what the extra capacity is for. With a 15 amp and a 10 amp machine connected, this generator still has 9.2 amps in hand, and with two 10 amp machines it has 14.2. A motor starting on top of the other one running is absorbed rather than tripping the unit. On the two smaller models the same pair leaves nothing, which is why we rate those for one machine at a time.
Australian machines are either 10 amp or 15 amp. Where two machines are listed together, they use one 15 amp outlet each.
| Combination | Supply it needs | On the iGen10000PRO |
|---|---|---|
| Kranzle KHD10/122 TST alone | 15 amp | Barely loads the engine |
| 15 amp Kranzle plus Chicago Pneumatic CPRC 2.5-50 | 25 A | Runs together, 9.2 A in hand for surge |
| 15 amp Kranzle plus Chicago Pneumatic Whisper 2-50 | 25 A | Runs together, 9.2 A in hand for surge |
| 15 amp Kranzle plus BigBoi BlowR PRO+ MKII | 25 A | Runs together, 9.2 A in hand for surge |
| BigBoi WashR Tradie or WashR Flo plus a compressor | 20 A | Two 10 amp machines, 14.2 A in hand |
| Kranzle KHD7/122TS plus a compressor | 20 A | Two 10 amp machines, 14.2 A in hand |
| Kranzle K1152TST plus a compressor | 25 A | Runs together, 9.2 A in hand for surge |
| Compressor alone, running continuously | 10 amp | Uses under a third of capacity |
| Lights, chargers and small equipment alongside a machine | Small non-motor loads | Fine, keep each outlet under 15 A |
| A third motor load on top of two machines | Over 30 A of supply | Ask us first. Two outlets, and surge headroom starts to disappear |
| Charging 12V equipment | 12V DC, 8 A, 100 W | Separate DC outlet, does not use the 240V capacity |
The 32 to 15 amp adaptor comes in the box, so the 32 amp socket becomes a standard 15 amp outlet. Plug the pressure washer into one, the compressor into the other. Both machines use ordinary plugs, and because a 10 amp plug fits a 15 amp socket, a 10 amp compressor or blower goes straight in without an adaptor. No special leads, no distribution board, no electrician. Both outlets sit behind the same RCD safety switch.
Before you order: Petrol generators must be run outdoors in open air. Never run one inside a van, trailer, garage or any enclosed space, and keep the exhaust away from open doors and windows. Carbon monoxide is odourless.
This generator is designed for standalone plug and socket connection to portable equipment. Any connection to a building's fixed wiring must be done by a licensed electrician with the correct changeover equipment.
At 109 kg wet, check your vehicle's payload and how the generator will be restrained before you fit it into a van.
| Specification | Detail |
|---|---|
| Maximum starting power | 10,000 W |
| Continuous running power | 8,200 WRated output at 1.0 power factor. |
| Continuous running current | 34.2 A |
| Output | 240V, 50 Hz, single phase |
| Receptacles | 1 x 32 A IP66 and 1 x 15 A IP66A 32 to 15 amp adaptor is supplied, so in practice you have two standard 15 amp outlets. A 10 amp plug fits a 15 amp socket. |
| 12V DC output | 12V, 8 A maximum, 100 W, IP44 receptacle |
| Voltage and waveform control | Digital inverter, pure sine wave output |
| Total harmonic distortion | Less than 2.5%Safe for electronically controlled equipment. |
| RCD safety switch | Yes, approved for workplace use |
| Alternator | Brushless, permanent magnetNo brushes to wear out or replace. |
| Engine | 457 cc, 1 cylinder, 4 stroke, overhead valve, air cooled |
| Maximum engine speed | 3,600 rpmThe lowest maximum speed in the range, which is part of why it stays quiet. |
| Fuel | Unleaded petrol, 91, 95 or 98 RONEthanol blends such as E10 are not recommended. |
| Fuel tank capacity | 30 litres |
| Run time at 1/4 and full load | 19.8 hours / 7.3 hours |
| Noise level at 1/4 and full load | 58 / 68 dB(A) at 7 m |
| Oil capacity and viscosity | 1.1 litres, SAE 10W-30 |
| Low oil shutdown and alarm | Yes |
| Maintenance | Engine oil and air filter servicing without tools |
| Starting method | Local and remote electric, plus recoil backup |
| Battery | 12V lithium-ion, with plug-in charger |
| Overload protection | Electronic, with indicator and push button reset |
| Data centre display | Output power and voltage, fuel level, fuel and cumulative run times |
| Spark plug | Torch F7RTC |
| Generator dimensions (L x W x H) | 767 x 630 x 675 mm |
| Weight, dry / wet | 85 kg / 109 kg |
| Packed dimensions and weight | 790 x 605 x 740 mm, 95 kg |
| Product code | WP iGen10000PRO |
| Warranty | 2 year domestic use, conditions apply |
Every PRO model has the same 15 amp IP66 outlet and the same RCD safety switch, so your leads and machines plug in identically whichever one you choose. What changes is how many outlets there are and how much capacity sits behind them.
| iGen4750PRO | iGen7500PRO | iGen10000PRO |
|---|---|---|
| 3,800 running watts | 6,000 running watts | 8,200 running watts |
| 15.8 A continuous | 25 A continuous | 34.2 A continuous |
| One 15 amp outlet | Two 15 amp outlets | Two 15 amp outlets and 12V DC |
| One machine at a time | One machine with large reserve | Compressor and washer together |
| 36 kg dry | 60 kg dry | 85 kg dry |
| 12 L tank, 14 h at 1/4 load | 15 L tank, 14.6 h at 1/4 load | 30 L tank, 19.8 h at 1/4 load |
| Lead acid battery | Lead acid battery | Lithium-ion battery |
Yes. That is exactly what this model is for. Starting a 1.86 kW compressor while a 1.8 kW washer is already running calls for about 6,450 watts at that instant, on the standard two and a half times rule. This generator supplies 10,000 starting watts, so there is roughly 3,550 watts spare. Plug one machine into each 15 amp outlet.
A 15 amp machine and a 10 amp machine need 25 amps of supply, which is the iGen7500PRO's entire rating. Starting one while the other runs calls for about 6,450 watts against its 7,500, leaving roughly a thousand watts and no spare socket capacity. A compressor cutting in while a pressure washer is running is a large momentary load, and it happens constantly through a working day, so we rate the iGen7500PRO for one machine at a time.
Yes. In Australia a 10 amp plug fits a 15 amp socket, because the 15 amp socket has a larger earth pin opening. A 10 amp compressor or blower plugs straight in with no adaptor. The reverse is not true, which is why a 15 amp machine cannot be plugged into a 10 amp point.
No. The 32 to 15 amp adaptor is supplied in the box, so both outlets take ordinary 15 amp plugs. Nothing extra to buy and no electrician required.
58 dB(A) at quarter load against 57 dB(A) for the two smaller units, measured at 7 metres. The 457 cc engine runs to a maximum of 3,600 rpm, the lowest in the range, and inverter control lets engine speed follow the load instead of holding a fixed speed.
A conventional fixed speed generator holds its engine at a set speed regardless of load. This one varies engine speed with demand, which is where the lower fuel use, lower noise and long quarter load run time come from, and it produces pure sine wave output rather than relying on an AVR to regulate a fixed speed alternator.
It powers the electric start and the remote control. This model uses a lithium-ion battery rather than the maintenance free lead acid battery in the two smaller units. A plug-in charger is supplied to keep it topped up between jobs.
The generator is 767 x 630 x 675 mm and weighs 85 kg dry, 109 kg with oil and fuel. It has wheels and a foldable handle. Check your payload and plan how it will be restrained. It is not designed to be lifted in and out each day.
Up to 19.8 hours at quarter load, or 7.3 hours at full load, from the 30 litre tank. Running a washer and a compressor together sits between those points, so a full day without refuelling is realistic.
Yes. Press the test button on the RCD before each job and confirm it trips. That takes a few seconds and is the only way to know the protection is working. All PRO models have the RCD fitted from the factory.
Equipment suitability above is general guidance based on the manufacturer's published supply requirements for each machine, not a performance guarantee. Actual results depend on your equipment, lead length and condition, ambient temperature, altitude and how continuously you run the load. Specifications are supplied by Westinghouse Outdoor Power Equipment and are subject to change without notice. If you are unsure whether this generator suits your setup, contact us with a list of your machines before ordering.
| Document Name | File Type | Download |
|---|---|---|
| Westinghouse iGen10000PRO Spec Sheet 1 | Download |
Please allow extra time for delivery to regional and remote areas.
Free Shipping on orders over $150 excluding remote areas and certain weight restrictions apply for free shipping in each state. Trade accounts $250 minimum for free shipping.
The following qualifies for free shipping:
For orders with free shipping, we determine whether to use a courier service or Australia Post based on the address. If you prefer your order to be shipped via Australia Post, please select the "Parcel Post" option at checkout.
Note: We do not ship to PO Boxes or Parcel Lockers with free shipping.
If your parcel is returned to us, the following conditions outline when additional shipping costs may apply:
*We will not be held responsible for delays or late delivery of Australia Post or courier services.
*If a parcel does not arrive as anticipated, please allow 5-7 working days for Australia Post or couriers to complete process of tracking and locating as in most cases it turns up after 3-7 days of expected delivery. We cannot refund or send another item until this process is completed.
*We don't take responsibility for orders that are lost or stolen once the parcel has been delivered to the correct delivery address.
*Items that are over 21kg may require to pay extra freight costs if in regional or remote areas - we will contact you if this is the case.
All of our prices are in Australian dollars (AUD) and include GST (Goods and services tax)
At Detailing Shed, we're a family-owned business that genuinely wants you to be happy with your purchase.
If something isn't right, please contact us before returning anything. In many cases, we can help resolve the issue with product advice, troubleshooting, or support from our team.
This policy explains how returns, refunds and warranty-related claims are handled while respecting your rights under Australian Consumer Law.
Nothing in this policy limits or replaces your rights under Australian Consumer Law.
If a product has a major or minor failure, you may be entitled to a remedy under Australian Consumer Law. The terms below primarily apply to change-of-mind purchases and circumstances not covered by consumer guarantees.
We may accept approved change-of-mind returns subject to the following conditions:
To request a return, email info@detailingshed.com.au with:
Due to safety, hygiene, freight and manufacturer restrictions, the following products are not eligible for change-of-mind returns:
These products cannot be returned for change of mind unless required under Australian Consumer Law.
With prior approval, we may accept returns on unused and unopened items such as:
Please contact us before sending anything back.
If you believe a product isn't performing correctly, please contact us before returning it.
To help us assess the issue, please provide:
In some cases, we may ask you to return the product for inspection.
If testing shows the product is operating as intended, the matter may be treated as a change-of-mind return and the standard conditions above may apply.
Products excluded from change-of-mind returns remain ineligible for return where no fault is found.
For orders shipped to New Zealand, customers are responsible for return shipping costs when sending back:
This applies to inspections, repairs and warranty-related claims.
Due to the high cost of international freight, we are unable to cover these return shipping costs.
If you've ordered the wrong item, you're welcome to return eligible products under this policy and place a new order for the correct item.
If you're unsure which product is right for you, our team is happy to help.
Orders can be cancelled before they have been processed or dispatched.
Approved cancellations will be refunded to the original payment method less a 3% payment processing fee.
Once an order has been processed or shipped, it can no longer be cancelled. However, eligible items may still be returned under our Change of Mind Returns policy.
If your order arrives damaged, incorrect or faulty, please contact us within 10 days of delivery.
Email info@detailingshed.com.au and include:
We'll work with you to assess the issue and determine an appropriate resolution.
If your parcel appears to be missing, we'll work with the carrier to investigate.
Please allow 7-15 business days for the investigation to be completed before a resolution can be finalised.
Manufacturers occasionally update packaging, labels and colours without notice.
As a result, the product you receive may vary slightly from the images shown on our website. This alone does not constitute a fault provided the correct product has been supplied.
Discount codes must be applied during checkout.
Unfortunately, discounts cannot be applied retrospectively and we cannot refund the difference after an order has been placed.
If you're experiencing issues with a discount code, please contact us before completing your purchase.
We're always happy to help.
Email: info@detailingshed.com.auinfo@detailingshed.com.au
When contacting us, please include:
Our team will do their best to resolve your enquiry quickly and fairly.
We're here to help
If you need to contact us for advice on any of the products, please email us at info@detailingshed.com.au
Please include description of the product you are interested. Some info of you car, and also what you are trying to achieve.
We may also review our blogs for product recommendations.
