FREE Shipping on orders over $150 (Weight Restrictions Apply)
2.2 hp. 210 L/min FAD. 60 litre tank. Standard 10A outlet. The Puma P14-60L is the entry point into the range and the most compact model we stock, sized to run from a standard 10A outlet without electrical work. Puma have been sold in Australia for over 40 years and are supported here by Glenco Air & Power.
Best Puma compressor for mobile detailers needing a compact 10A setup for blow guns, tyre inflation and intermittent interior cleaning gun use.
| Application | Suitability |
|---|---|
| Blow guns | ExcellentWell suited to typical blow-gun use. |
| Air blow-out and detailing tools | ExcellentWell suited to typical detailing work. |
| Tornador-style interior guns | Suitable210 L/min covers this, though sustained use will cycle the motor often. |
| Pneumatic polishers | Check requirementsCheck your polisher's stated air consumption against 210 L/min before ordering. |
| Pneumatic sanders | Check requirementsSanders are among the highest-draw tools. Confirm requirements first. |
| Multiple air tools at once | Check requirementsDepends entirely on which tools. Contact us with your list. |
| High-consumption tools | Check requirementsLikely to exceed this compressor's output. Consider the P22 or three-phase range. |
Ratings above are guidance based on the compressor's Free Air Delivery against typical air consumption for each tool type. They are not a performance guarantee. Actual results depend on your specific tools, working pressure, air line setup and how continuously you run them. Check your tool's air requirement before ordering, or get in touch and we will check it for you.
The usable output figure, not pump displacement. This is what actually reaches your tool.
Enough buffer for burst work such as blowing out panels and wheel arches between passes.
Sized to run on a standard 10 amp circuit, so no switchboard work is needed.
The same pump family used across the 240V range, running at a slow 1,100 rpm.
Belt drive turns the pump slower than direct drive, which means less heat and longer pump life.
A 5 micron filter regulator is fitted as standard, removing dirt and water and giving accurate pressure control, with a Nitto-style coupling on the outlet.
The 240V motor was developed and tested in Australia. Totally enclosed fan-cooled construction keeps dirt and moisture out of the windings.
Solid rubber on steel wheels with ball bearing hubs. Never goes flat, moves easily across a workshop floor.
Compressor air output is quoted two different ways, and the difference catches a lot of buyers out.
Pump displacement is the volume the pump sweeps on every rotation. It is a theoretical figure and it is always the larger of the two, which is why it often appears first in marketing.
Free Air Delivery (FAD) is the air that actually reaches your tool once losses through the valves, rings and heat are accounted for. This is the number that determines whether your equipment will run properly.
We list FAD as the headline figure on every Puma page. If you are comparing this against another compressor and that one only quotes displacement, you are not comparing like with like. Always ask for the FAD figure.
| Specification | Detail |
|---|---|
| Motor | 2.2 hp / 1.65 kW |
| Pump displacement | 270 L/min (9.5 cfm)Theoretical figure. |
| Free air delivery (FAD) | 210 L/min (7.4 cfm)Use this figure when comparing compressors. |
| Maximum pressure | 1,000 kPa (145 psi)Most detailing tools run at 600 to 800 kPa. |
| Tank capacity | 60 Litres |
| Voltage | 240V |
| Phase | Single phase |
| Current | 10 AmpsStandard 10A outlet. |
| Pump model | Puma PG21 |
| Pump speed | 1,100 rpm |
| Pump type | Piston, oil-lubricated, belt-driven |
| Outlet size | 1/4" with Nitto-style coupling fitted |
| Noise level | 73 dB(A)Measured at 1 m per AS 2221.1-1979. The quietest in the 240V Puma range. |
| Weight | 84 kg |
| Dimensions (L x W x H) | 112 x 46 x 72 cm |
| Warranty | 12 monthsGlenco Air & Power warranty against defects. |
| Delivery | Standard courier, wheeled unit |
A compressor on its own is only the starting point. What reaches your tool depends just as much on filtration and pipework.
Glenco publish a full maintenance schedule for oil-lubricated compressors. Keeping to it is what determines how many years you get out of the pump.
| Interval | Task |
|---|---|
| Daily | Check the oil level and inspect for oil leaks. Drain accumulated condensate from the tank; daily draining is recommended where the compressor is used frequently. |
| Weekly | Check or clean the air filter, test the safety valve, inspect for air leaks. |
| Monthly | Check the V-belt, tighten fasteners, clean the unit. |
| 3 months or 500 hours | Replace the oil. |
| 12 months or 2,000 hours | Replace the air filter. |
| 2 years or 4,000 hours | Replace the filter-regulator and V-belt. |
Consumables including filters, lubricants and V-belts are not covered by warranty. Service intervals should be shortened in harsher working conditions.
| Model | FAD | Tank | Power | Max pressure | Best for |
|---|---|---|---|---|---|
| P14-60L | 210 L/min | 60 L | 240V 10A | 1,000 kPa | Mobile detailing and home garages |
| P16-100L | 240 L/min | 100 L | 240V 10A | 800 kPa | Most air available on a standard 10A outlet |
| P18-100L | 320 L/min | 100 L | 240V 15A | 1,000 kPa | When you need 145 psi on single phase |
| P22-100L | 350 L/min | 100 L | 240V 15A | 800 kPa | Most air available on single phase |
| P22-120L | 350 L/min | 120 L | 240V 15A | 800 kPa | Sustained use, largest single-phase tank |
| P30 415V | 520 L/min | 140 L | 415V 3ph | 1,000 kPa | Multiple operators, entry three phase |
| P55 415V | 1,055 L/min | 265 L | 415V 3ph | 800 kPa | High-volume multi-bay workshops |
Free air delivery is the figure to size your tools against. Higher pressure and higher flow are a trade-off at each amp rating, so pick based on what your tools actually require.
210 L/min free air delivery (7.4 cfm) at up to 1,000 kPa (145 psi). Pump displacement is 270 L/min, but FAD is the figure to compare against your tools.
Free Air Delivery. It is the air that actually reaches your tool after losses inside the pump, as opposed to pump displacement which is the theoretical volume the pump sweeps. FAD is always the lower number and always the more useful one.
Blow guns, tyre inflators and general detailing blow-out tools comfortably. Interior cleaning guns are workable. For pneumatic sanders or polishers, check the tool's air requirement against 210 L/min first.
This depends entirely on which tools and how continuously they run, so we do not quote a fixed number. Send us your equipment list and we will work it out properly.
240V single phase from a standard 10A outlet. No dedicated circuit is normally required, though we would not recommend sharing the circuit with other heavy loads.
Yes, for a single operator doing blow-drying, tyre inflation and interior work. A 5 micron filter regulator is fitted as standard, so you do not need to buy a basic filter. For paint, coating or PPF work, add a suitable coalescing filter downstream to reduce oil aerosol.
Delivery is charged at cost for this model. Contact us with your postcode for a freight quote.
No. It plugs into a standard power point and is ready to use once you have checked the oil level.
Glenco Air & Power provide a 12 month warranty against defects in material and workmanship from the date of original sale. Electric motors carry whatever warranty the motor manufacturer provides. Consumables including filters, lubricants and V-belts are not covered, nor is normal wear and tear. Keep your tax invoice as proof of purchase.
Glenco publish a full schedule. Daily: check the oil level, inspect for oil leaks and drain the air tank. Weekly: check or clean the air filter, test the safety valve and inspect for air leaks. Monthly: check the V-belt, tighten fasteners and clean the unit. Every 3 months or 500 hours: replace the oil. Every 12 months or 2,000 hours: replace the air filter. Every 2 years or 4,000 hours: replace the filter-regulator and V-belt.
Not sure which Puma compressor is right for your tools? Compare the range above, or use our Air Line Configurator to size the whole system.
Plan Your Air Line Compare All Puma CompressorsPlease allow extra time for delivery to regional and remote areas.
Free Shipping on orders over $150 excluding remote areas and certain weight restrictions apply for free shipping in each state. Trade accounts $250 minimum for free shipping.
The following qualifies for free shipping:
For orders with free shipping, we determine whether to use a courier service or Australia Post based on the address. If you prefer your order to be shipped via Australia Post, please select the "Parcel Post" option at checkout.
Note: We do not ship to PO Boxes or Parcel Lockers with free shipping.
If your parcel is returned to us, the following conditions outline when additional shipping costs may apply:
*We will not be held responsible for delays or late delivery of Australia Post or courier services.
*If a parcel does not arrive as anticipated, please allow 5-7 working days for Australia Post or couriers to complete process of tracking and locating as in most cases it turns up after 3-7 days of expected delivery. We cannot refund or send another item until this process is completed.
*We don't take responsibility for orders that are lost or stolen once the parcel has been delivered to the correct delivery address.
*Items that are over 21kg may require to pay extra freight costs if in regional or remote areas - we will contact you if this is the case.
All of our prices are in Australian dollars (AUD) and include GST (Goods and services tax)
At Detailing Shed, we're a family-owned business that genuinely wants you to be happy with your purchase.
If something isn't right, please contact us before returning anything. In many cases, we can help resolve the issue with product advice, troubleshooting, or support from our team.
This policy explains how returns, refunds and warranty-related claims are handled while respecting your rights under Australian Consumer Law.
Nothing in this policy limits or replaces your rights under Australian Consumer Law.
If a product has a major or minor failure, you may be entitled to a remedy under Australian Consumer Law. The terms below primarily apply to change-of-mind purchases and circumstances not covered by consumer guarantees.
We may accept approved change-of-mind returns subject to the following conditions:
To request a return, email info@detailingshed.com.au with:
Due to safety, hygiene, freight and manufacturer restrictions, the following products are not eligible for change-of-mind returns:
These products cannot be returned for change of mind unless required under Australian Consumer Law.
With prior approval, we may accept returns on unused and unopened items such as:
Please contact us before sending anything back.
If you believe a product isn't performing correctly, please contact us before returning it.
To help us assess the issue, please provide:
In some cases, we may ask you to return the product for inspection.
If testing shows the product is operating as intended, the matter may be treated as a change-of-mind return and the standard conditions above may apply.
Products excluded from change-of-mind returns remain ineligible for return where no fault is found.
For orders shipped to New Zealand, customers are responsible for return shipping costs when sending back:
This applies to inspections, repairs and warranty-related claims.
Due to the high cost of international freight, we are unable to cover these return shipping costs.
If you've ordered the wrong item, you're welcome to return eligible products under this policy and place a new order for the correct item.
If you're unsure which product is right for you, our team is happy to help.
Orders can be cancelled before they have been processed or dispatched.
Approved cancellations will be refunded to the original payment method less a 3% payment processing fee.
Once an order has been processed or shipped, it can no longer be cancelled. However, eligible items may still be returned under our Change of Mind Returns policy.
If your order arrives damaged, incorrect or faulty, please contact us within 10 days of delivery.
Email info@detailingshed.com.au and include:
We'll work with you to assess the issue and determine an appropriate resolution.
If your parcel appears to be missing, we'll work with the carrier to investigate.
Please allow 7-15 business days for the investigation to be completed before a resolution can be finalised.
Manufacturers occasionally update packaging, labels and colours without notice.
As a result, the product you receive may vary slightly from the images shown on our website. This alone does not constitute a fault provided the correct product has been supplied.
Discount codes must be applied during checkout.
Unfortunately, discounts cannot be applied retrospectively and we cannot refund the difference after an order has been placed.
If you're experiencing issues with a discount code, please contact us before completing your purchase.
We're always happy to help.
Email: info@detailingshed.com.auinfo@detailingshed.com.au
When contacting us, please include:
Our team will do their best to resolve your enquiry quickly and fairly.
We're here to help
If you need to contact us for advice on any of the products, please email us at info@detailingshed.com.au
Please include description of the product you are interested. Some info of you car, and also what you are trying to achieve.
We may also review our blogs for product recommendations.
