FREE Shipping on orders over $150 (Weight Restrictions Apply)
5.5 hp. 520 L/min FAD. 140 litre tank. 415V three phase. Free delivery. The Puma P30 is the entry point into three-phase, which is what lets several people draw air at the same time without pressure collapsing at the furthest outlet. Draws 8.3 amps running on a 16 amp breaker.
Best entry-level three-phase Puma for multi-bay workshops where more than one operator needs air at the same time.
| Application | Suitability |
|---|---|
| Blow guns | ExcellentWell suited to typical blow-gun use. |
| Air blow-out and detailing tools | ExcellentAmple headroom for typical detailing work. |
| Tornador-style interior guns | ExcellentComfortable, including continuous use. |
| Pneumatic polishers | ExcellentSuitable for sustained use. |
| Pneumatic sanders | Excellent520 L/min handles sanders comfortably. |
| Multiple air tools at once | SuitableThis is what three-phase is for. Contact us with your tool list to confirm the combination. |
| High-consumption tools | SuitableCheck the specific requirement against 520 L/min. |
Ratings above are guidance based on the compressor's Free Air Delivery against typical air consumption for each tool type. They are not a performance guarantee. Actual results depend on your specific tools, working pressure, air line setup and how continuously you run them. Check your tool's air requirement before ordering, or get in touch and we will check it for you.
Roughly 49 percent more air than the largest single-phase Puma, which is what enables simultaneous use.
Sized to buffer demand spikes when several outlets draw at once.
Three-phase motors run more smoothly and efficiently under continuous load than single-phase equivalents.
Modest current draw for the output, on a 16 amp breaker.
Slower pump speed than direct drive, less heat and longer service life under continuous duty.
Ships palletised at no delivery cost.
Compressor air output is quoted two different ways, and the difference catches a lot of buyers out.
Pump displacement is the volume the pump sweeps on every rotation. It is a theoretical figure and it is always the larger of the two, which is why it often appears first in marketing.
Free Air Delivery (FAD) is the air that actually reaches your tool once losses through the valves, rings and heat are accounted for. This is the number that determines whether your equipment will run properly.
We list FAD as the headline figure on every Puma page. If you are comparing this against another compressor and that one only quotes displacement, you are not comparing like with like. Always ask for the FAD figure.
| Specification | Detail |
|---|---|
| Motor | 5.5 hp |
| Pump displacement | Contact usContact us for this figure. |
| Free air delivery (FAD) | 520 L/min (18.4 cfm)Use this figure when comparing compressors. |
| Maximum pressure | 1,000 kPa (145 psi) |
| Tank capacity | 140 Litres |
| Voltage | 415V |
| Phase | Three phase |
| Running current | 8.3 Amps |
| Circuit breaker rating | 16 AmpsRequired breaker size for installation. |
| Pump model | Contact us |
| Pump speed | Contact us |
| Pump type | Piston, oil-lubricated, belt-driven |
| Outlet size | Contact usContact us to confirm before ordering fittings. |
| Noise level | Contact us |
| Weight | Contact us |
| Dimensions | Contact us |
| Warranty | 12 monthsGlenco Air & Power warranty against defects. |
| Delivery | Palletised, free delivery |
A compressor on its own is only the starting point. What reaches your tool depends just as much on filtration and pipework.
Glenco publish a full maintenance schedule for oil-lubricated compressors. Keeping to it is what determines how many years you get out of the pump.
| Interval | Task |
|---|---|
| Daily | Check the oil level and inspect for oil leaks. Drain accumulated condensate from the tank; daily draining is recommended where the compressor is used frequently. |
| Weekly | Check or clean the air filter, test the safety valve, inspect for air leaks. |
| Monthly | Check the V-belt, tighten fasteners, clean the unit. |
| 3 months or 500 hours | Replace the oil. |
| 12 months or 2,000 hours | Replace the air filter. |
| 2 years or 4,000 hours | Replace the filter-regulator and V-belt. |
Consumables including filters, lubricants and V-belts are not covered by warranty. Service intervals should be shortened in harsher working conditions.
| Model | FAD | Tank | Power | Max pressure | Best for |
|---|---|---|---|---|---|
| P14-60L | 210 L/min | 60 L | 240V 10A | 1,000 kPa | Mobile detailing and home garages |
| P16-100L | 240 L/min | 100 L | 240V 10A | 800 kPa | Most air available on a standard 10A outlet |
| P18-100L | 320 L/min | 100 L | 240V 15A | 1,000 kPa | When you need 145 psi on single phase |
| P22-100L | 350 L/min | 100 L | 240V 15A | 800 kPa | Most air available on single phase |
| P22-120L | 350 L/min | 120 L | 240V 15A | 800 kPa | Sustained use, largest single-phase tank |
| P30 415V | 520 L/min | 140 L | 415V 3ph | 1,000 kPa | Multiple operators, entry three phase |
| P55 415V | 1,055 L/min | 265 L | 415V 3ph | 800 kPa | High-volume multi-bay workshops |
Free air delivery is the figure to size your tools against. Higher pressure and higher flow are a trade-off at each amp rating, so pick based on what your tools actually require.
520 L/min free air delivery (18.4 cfm) at up to 1,000 kPa (145 psi).
Free Air Delivery, the air that actually reaches your tools. Pump displacement is the theoretical swept volume and always reads higher. FAD is the honest comparison figure.
Everything in a typical detailing or automotive workshop, including pneumatic sanders and polishers. The advantage of three-phase is running more than one at a time.
This depends on the specific tools and their duty cycle, so we do not quote a fixed number. Send us your equipment list and we will size the system properly, including the pipework.
415V three phase, drawing 8.3 amps running with a 16 amp circuit breaker. A licensed electrician must carry out the connection.
Yes, particularly for multi-bay operations. Fit filtration between the compressor and your air line, since this is oil-lubricated and oil carryover will contaminate paint and coatings.
Yes, this model ships palletised with free delivery. Confirm you have suitable access and a way to unload.
Yes. Three-phase connection must be carried out by a licensed electrician.
Glenco Air & Power provide a 12 month warranty against defects in material and workmanship from the date of original sale. Electric motors carry whatever warranty the motor manufacturer provides. Consumables including filters, lubricants and V-belts are not covered, nor is normal wear and tear. Keep your tax invoice as proof of purchase.
Glenco publish a full schedule. Daily: check the oil level, inspect for oil leaks and drain the air tank. Weekly: check or clean the air filter, test the safety valve and inspect for air leaks. Monthly: check the V-belt, tighten fasteners and clean the unit. Every 3 months or 500 hours: replace the oil. Every 12 months or 2,000 hours: replace the air filter. Every 2 years or 4,000 hours: replace the filter-regulator and V-belt.
Not sure which Puma compressor is right for your tools? Compare the range above, or use our Air Line Configurator to size the whole system.
Plan Your Air Line Compare All Puma CompressorsPlease allow extra time for delivery to regional and remote areas.
Free Shipping on orders over $150 excluding remote areas and certain weight restrictions apply for free shipping in each state. Trade accounts $250 minimum for free shipping.
The following qualifies for free shipping:
For orders with free shipping, we determine whether to use a courier service or Australia Post based on the address. If you prefer your order to be shipped via Australia Post, please select the "Parcel Post" option at checkout.
Note: We do not ship to PO Boxes or Parcel Lockers with free shipping.
If your parcel is returned to us, the following conditions outline when additional shipping costs may apply:
*We will not be held responsible for delays or late delivery of Australia Post or courier services.
*If a parcel does not arrive as anticipated, please allow 5-7 working days for Australia Post or couriers to complete process of tracking and locating as in most cases it turns up after 3-7 days of expected delivery. We cannot refund or send another item until this process is completed.
*We don't take responsibility for orders that are lost or stolen once the parcel has been delivered to the correct delivery address.
*Items that are over 21kg may require to pay extra freight costs if in regional or remote areas - we will contact you if this is the case.
All of our prices are in Australian dollars (AUD) and include GST (Goods and services tax)
At Detailing Shed, we're a family-owned business that genuinely wants you to be happy with your purchase.
If something isn't right, please contact us before returning anything. In many cases, we can help resolve the issue with product advice, troubleshooting, or support from our team.
This policy explains how returns, refunds and warranty-related claims are handled while respecting your rights under Australian Consumer Law.
Nothing in this policy limits or replaces your rights under Australian Consumer Law.
If a product has a major or minor failure, you may be entitled to a remedy under Australian Consumer Law. The terms below primarily apply to change-of-mind purchases and circumstances not covered by consumer guarantees.
We may accept approved change-of-mind returns subject to the following conditions:
To request a return, email info@detailingshed.com.au with:
Due to safety, hygiene, freight and manufacturer restrictions, the following products are not eligible for change-of-mind returns:
These products cannot be returned for change of mind unless required under Australian Consumer Law.
With prior approval, we may accept returns on unused and unopened items such as:
Please contact us before sending anything back.
If you believe a product isn't performing correctly, please contact us before returning it.
To help us assess the issue, please provide:
In some cases, we may ask you to return the product for inspection.
If testing shows the product is operating as intended, the matter may be treated as a change-of-mind return and the standard conditions above may apply.
Products excluded from change-of-mind returns remain ineligible for return where no fault is found.
For orders shipped to New Zealand, customers are responsible for return shipping costs when sending back:
This applies to inspections, repairs and warranty-related claims.
Due to the high cost of international freight, we are unable to cover these return shipping costs.
If you've ordered the wrong item, you're welcome to return eligible products under this policy and place a new order for the correct item.
If you're unsure which product is right for you, our team is happy to help.
Orders can be cancelled before they have been processed or dispatched.
Approved cancellations will be refunded to the original payment method less a 3% payment processing fee.
Once an order has been processed or shipped, it can no longer be cancelled. However, eligible items may still be returned under our Change of Mind Returns policy.
If your order arrives damaged, incorrect or faulty, please contact us within 10 days of delivery.
Email info@detailingshed.com.au and include:
We'll work with you to assess the issue and determine an appropriate resolution.
If your parcel appears to be missing, we'll work with the carrier to investigate.
Please allow 7-15 business days for the investigation to be completed before a resolution can be finalised.
Manufacturers occasionally update packaging, labels and colours without notice.
As a result, the product you receive may vary slightly from the images shown on our website. This alone does not constitute a fault provided the correct product has been supplied.
Discount codes must be applied during checkout.
Unfortunately, discounts cannot be applied retrospectively and we cannot refund the difference after an order has been placed.
If you're experiencing issues with a discount code, please contact us before completing your purchase.
We're always happy to help.
Email: info@detailingshed.com.auinfo@detailingshed.com.au
When contacting us, please include:
Our team will do their best to resolve your enquiry quickly and fairly.
We're here to help
If you need to contact us for advice on any of the products, please email us at info@detailingshed.com.au
Please include description of the product you are interested. Some info of you car, and also what you are trying to achieve.
We may also review our blogs for product recommendations.
